Dual-curing adhesive systems are ideal for post fastening.
With the combination of Pre-Bond, an activator that promotes polymerization, it ensures strong adhesion between enamel and dentin. Particularly suitable for post bonding, abutment restoration, veneers, inlays, onlays, bridges and crowns.Sort by:
- Featured
- Most relevant
- Best selling
- Alphabetically, A-Z
- Alphabetically, Z-A
- Price, low to high
- Price, high to low
- Date, old to new
- Date, new to old
Adhesive system (2)
Adhesive system (2)
THÀNH PHẦN:
- 5–15% 4-Methacryloxyethyl trimellitate anhydride (4-META)
- 5–15% 10-Methacryloyloxydecyl dihydrogen phosphate (MDP)
- 15–25% Dimethacrylate monomer
- Thiophosphate ester monomer (MDTP)
- 20–30% Purified water (Nước tinh khiết)
- 25–35% Acetone
- Photo initiator (Chất khởi tạo quang trùng hợp)
- 1–10% Silica fine powder (Bột silica mịn)
CHỈ ĐỊNH SỬ DỤNG
- G-Premio BOND là keo dán nha khoa quang trùng hợp, một thành phần, thế hệ 8, dùng để tạo liên kết giữa vật liệu phục hồi và mô răng. Sản phẩm có thể sử dụng với cả 3 kỹ thuật total-etch, self-etch và selective-etch
- Gắn trực tiếp composite và compomer quang trùng hợp vào cấu trúc răng.
- Gắn composite tái tạo cùi răng (loại trùng hợp kép) vào cấu trúc răng, với điều kiện các vật liệu này phải được quang trùng hợp.
- Sửa chữa tại chỗ các phục hình composite, phục hình nền kim loại và phục hình zirconia/alumina.
- Sửa chữa tại chỗ các phục hình sứ khi kết hợp với chất liên kết silane.
- Điều trị răng nhạy cảm.
- Bít kín bề mặt răng đã sửa soạn (xoang trám hoặc cùi răng) cho các phục hình gián tiếp.
- Có thể sử dụng kết hợp với resin cement nhờ lớp màng sau xử lý rất mỏng, khoảng 3 µm.
CHỐNG CHỈ ĐỊNH
- Che tủy.
- Tránh sử dụng sản phẩm này cho bệnh nhân đã biết có dị ứng với monomer methacrylate, polymer methacrylate hoặc acetone.
LuxaBond - Total Etch
Silane ensures good adhesion between the pin and the cement.
After the Silane post is secured and the root canal is prepared with LuxaBondTotal Etch, Luxa-Core Z-Dual dual-curing cement will be used to bond the fiber post to the root canal. Then, the tooth preparation will be completed with the help of LuxaCore Z-Dual.
User manual
It will be cleaned and glued. I used DMG's Silane, which consists of two components and will be mixed in equal proportions just before use. After a working time of 1 minute, the excess will be blown away and the prepared dowel will be set aside.Prior to this, the tooth cavity (enamel and dentin) was treated with DMG etching gel, which could be safely delivered to the bottom of the root canal with an integrated endodontic syringe. Water was used after 60 seconds of phosphoric acid treatment on the enamel or 15 seconds on the dentin. I used a disposable syringe in water with an Endo-Luer endodontic syringe.
The root canal will now be dried using a paper cone, and the PreBond bipolymer from the LuxaBond-Total Etch system will be applied around the root canal surface with an Endobrush for 15 seconds. Excess material can be removed or will be extracted from the canal using a tissue tip.
One drop of each bond A and B will be mixed and applied to the root canal wall using an Endobrush for 20 seconds. Note that the curing time of the polymerized cement may be shortened by the activation of the Prebond active ingredient, as the post cannot be inserted or is not deep enough in this case. Excess material will be removed or absorbed by the paper tips to avoid larger residues.